1 x 2 Series Isolated, DC to DC Converters
“ER” Series
The “ER” Series DC to DC Converters have a single isolated output, which is highly regulated, and short circuit protected. These units are very well filtered and generate a minimum of noise and RFI.
“ER” Series
MAXIMUM OUTPUT POWER 1 – 1.5 WATTS
Packaging Size: 1 x 2 x .4 inches
- Isolated DC/DC Converters
- Highly Regulated Single Outputs
- Low Noise
- Six-Sided Electrostatic Shield
- Fully Encapsulated
5, 12, 24, 28, 48 VDC
Nominal Output Voltage:
5 to 24 VDC
“MU” Series
The “MU” Series units have single or dual isolated and well-filtered outputs, which are short circuit protected. Both input and output lines contain Pi filters.
“MU” Series
MAXIMUM OUTPUT POWER 5 WATTS
Packaging Size: 1 x 2 x .375 inches
- Isolated DC/DC Converters
- High Efficiency
- Encapsulated
- Output Tracks Input
- Internal six-sided electrostatic shield
- Single and dual outputs units available
Nominal Output Voltages: 5 to 24 VDC
“MR” Series
The “MR” Series units have single or dual outputs, which are highly regulated, and short circuit protected. These units are very well filtered and generate a minimum of noise and RFI. They provide an ultimate in performance when powering very sensitive circuits such as A to D converters.
“MR” Series
MAXIMUM OUTPUT POWER 2 WATTS
Packaging Size: 1 x 2 x .37 inches
- Isolated DC/DC Converters
- Highly regulated single outputs
- Low noise
- Internal six-sided electrostatic shield
- fully encapsulated
“MRS-WR” and “MRD-WR” Series
The “MRS-WR” and “MRD-WR” series units have outputs, which are well regulated, and short circuit protected. These units are very well filtered and generate a minimum of noise and RFI. All units are completely wrapped internally with one continuous copper sheet and then sealed with epoxy in an insulated enclosure.
“MRS-MR” Series
MAXIMUM OUTPUT POWER 9 WATTS
Packaging Size: 1 x 2 x .7 inches
- single isolated outputs
- wide input voltage range
- output highly regulated under all conditions of input voltage and output load. (no minimum loading required)
- one continuous copper shield covers the entire electronics internally to provide a tight six-sided electrostatic shield
- low output noise on all outputs
Special Applications: The MRS-WR DC to DC converters are designed for use in wide range input voltage applications such as battery inputs where high efficiency is of prime importance, however tradeoffs in design have been made to yield excellent regulations and low output ripple, regardless of load, while still operating at high efficiency.
“MRD-WR” Series
MAXIMUM OUTPUT POWER 3 – 0.8 WATTS Packaging Size: 1 x 2 x .60 – .70 inches
“MRS-MR” Series
MAXIMUM OUTPUT POWER 9 WATTS
Packaging Size: 1 x 2 x .7 inches
- dual isolated outputs
- all outputs highly regulated under all conditions of input voltage and output load.
- no minimum loading required. ¸ balanced loading is not required to maintain regulation on either output
- low output noise on all outputs
- balanced loading is not required to maintain regulation on either output
- 125 khz switching frequency
- copper shielded
Applications: The MRD-WR DC/DC Converters are designed for use in wide range input voltage applications such as battery inputs where high efficiency is of prime importance, however tradeoffs in design have been made to yield excellent regulation and low output ripple on each output individually, regardless of load on any output, while still operating at high efficiency.
“MRS-WRT” and “MRD-WRT” Series
The “MRS-WRT” and “MRD-WRT” Series units have outputs, which are well regulated, and short circuit protected. These units are very well filtered and generate a minimum of noise and RFI. All units are completely wrapped internally with one continuous copper sheet and then sealed with epoxy in an insulated enclosure.
“MRS-WRT” Series
MAXIMUM OUTPUT POWER 4.2 – 14.4 WATTS
Packaging Size: 1 x 2 x (.5- .7) inches
- single isolated outputs
- wide input voltage range
- all outputs highly regulated under all conditions of input voltage and output load. (no minimum loading required on any output.)
- one continuous copper shield covers the entire electronics internally to provide a tight six-sided electrostatic shield
- low output noise on all outputs
- no overshoot during turn-on or load changes
- 125 khz switching frequency
Applications: The MRS-WRT DC/DC Converts are designed for use in wide range input voltage applications such as battery inputs where high efficiency is of prime importance, however tradeoffs in design have been made to yield excellent regulation and low output ripple on each output, regardless of loading, while still operating at high efficiency.
“MRD-WRT” Series
MAXIMUM OUTPUT POWER 3 – 10 WATTS Packaging Size: 1 x 2 x (.5- .7) inches
- dual isolated outputs
- wide input voltage range
- all outputs highly regulated under all conditions of input voltage and output load. (no minimum loading required on any output.) (balance loading is not required to maintain regulation on either output.)
- one continuous copper shield covers the entire electronics internally to provide a tight six-sided electrostatic shield
- low output noise on all outputs
- no overshoot during turn-on or load changes
- 125 khz switching frequency
Applications: The MRD-WRT DC/DC Converters are designed for use in wide range input voltage applications such as battery inputs where high efficiency is of prime importance, however tradeoffs in design have been made to yield excellent regulation and low output ripple on each output, regardless of load on any output, while still operating at high efficiency.